Home >  Applications >  Set-top Box, Audio

Set-top Box, Audio

 

Battery powered wearables and fitness devices are typically very compact in size and have limited battery capacities.  These devices must use high efficiency power conversion to maximize user time between charging cycles.  For products with input power ports to connect battery charging devices, internal load circuit switching and power port protection are required. 

 

+ Voltage Regulation  

 

Set-top box and audio products AC/DC power supplies do not always provide specific voltage rails needed by application circuits. Voltage regulators allow device main voltage rails to be stepped up or down at the point of load for specific application circuits.

 

  • For light load current requirements, a dual output linear regulator provide a compact low cost voltage regulation solution.
  • When high power conversion efficiency is desired, a DC/DC switching regulator can be a better choice. DC/DC switching regulators are available for voltage step-up and step-down applications.

 

Part NumberDescriptionPackagePackage Alt.Package Alt.1
KTB851 600mA Step-down Converter with Output Load Discharge UTDFN-6 1.6 x1.6 x 0.55mm TDFN-6 1.6 x1.6 x 0.75mm TSOT23-5
KTB851-1 600mA Step-down Converter UTDFN-6 1.6 x1.6 x 0.55mm TDFN-6 1.6 x1.6 x 0.75mm TSOT23-5
KTA201 Low Noise, Fast Reponse Dual 150mA LDO Regulators SOT23-6 TDFN22-8  
KTC218 Wide Output Range Step-Up Converter SOT23-5 TSOT23-5  

+ EMI/ESD Suppression  

 

The AS1602 is an integrated ESD and Common Mode EMI suppression IC used to improve EMC performance in Ethernet applications. It is built around Kinetic Technologies' patented and proprietary Active EMC suppression technology to enable "Design for Compliance" approach to system design right from the start. This product helps eliminate EMC compliance challenges by providing consistent EMC performance and improvements utilizing silicon based technology as opposed to passive technologies. The AS1602 enables system designers to comply with:

 

  • CISPR22 and FCC Part 15, Class B requirements for Radiated and Conducted Emissions.
  • IEC 61000-4-3/6 requirements for Radiated and Conducted Immunity, Level 3 or higher.
  • IEC 61000-4-2 ESD (Air Discharge) of ±25kV.
  • IEC 61000-4-2 ESD (Contact Discharge) of ±12kV.
  • Cable Discharge Event (CDE) of ±12kV.

 

Part NumberDescriptionPackagePackage Alt.Package Alt.1
AS1602 Dual-channel Active choke for EMI suppression w/ Integrated ESD Protection QSOP-16L (SOIC narrow)    

+ LCD Backlight LED Drivers  

 

Set-top box LCD displays require LED backlighting. White LEDs are used for color displays and monochrome displays use fixed color LEDs.

 

  • Display backing power management solutions provide necessary voltage conversion for given LED strings and brightness control.
  • White LED (WLED) backlight driver solutions range from simple linear LED brightness control to sophisticated high efficiency WLED array drivers to cover most LCD panel sizes available today.
  • Programming options cover simple PWM signal control to full-featured I2C interfaces.

 

Part NumberDescriptionPackagePackage Alt.Package Alt.1
KTD104 Linear-mode 4-Channel LED Driver SOT23-8 TDFN22-8  
KTD105 Linear-mode 5-Channel LED Driver SOT23-8 TDFN22-8  
KTD108 Linear-mode 4-Channel LED Driver SOT23-8 TDFN33-16  
KTD109 Linear-mode 5-Channel LED Driver SOT23-8 TDFN33-16  
KTD117 Linear-mode 4+2 -Channel LED Driver TDFN33-12    
KTD251 Step-Up LED Driver with PWM Control TSOT23-6    
KTD2531 Step-Up LED Driver with PWM Control TSOT23-6    
KTD2536 Step-Up LED Driver with PWM Control TSOT23-6    
KTD2500 Step-Up LED Driver with ExpressWire or PWM Control TDFN22-6    
KTD2505R Step-Up LED Driver with ExpressWire or PWM Control TDFN22-6    
KTD2511C Step-Up LED Driver with PWM Control TSOT23-6 TDFN22-8    
KTD2511D Step-Up LED Driver with PWM Control TSOT23-6 TDFN22-8    
KTD2801 Step-Up LED Driver with Internal Diode and ExpressWire/PWM Dimming TSOT23-6 TDFN22-6    
KTD2801A Step-Up LED Driver with Internal Diode and ExpressWire/PWM Dimming TSOT23-6 TDFN22-6    
KTD314 High Efficiency, Wide Voltage Range 20-LED Driver TQFN33-16    
KTD315 High Efficiency, Wide Voltage Range 30-LED Driver TQFN33-16    
KTD3112 High Efficiency Step-Up 2-Ch LED Driver, 25V OVP TQFN33-16 WLCSP-9    
KTD3113 High Efficiency Step-Up 3-Ch LED Driver, 25V OVP TQFN33-16 WLCSP-9    
KTD3116-1 High Efficiency Step-Up 2-Ch LED Driver, 31V OVP WLCSP-9    
KTD3117-1 High Efficiency Step-Up 3-Ch LED Driver, 31V OVP WLCSP-9    
KTD3118 High Efficiency Step-Up 2-Ch LED Driver, 42V OVP WLCSP-9    
KTD3119 High Efficiency Step-Up 3-Ch LED Driver, 42V OVP WLCSP-9    
KTD3122 2-Ch Step-Up LED Driver with Integrated Power Diode TQFN33-16 WLCSP-12  
KTD3156 6-Ch Step-Up LED Driver with PWM-Control Mixed-Mode Dimming TQFN33-16 WLCSP-16  
KTD3156B 6-Ch Step-Up LED Driver with PWM-Control Mixed-Mode Dimming, low duty dimming TQFN33-16 WLCSP-16  
KTD325 High Efficiency, Wide Voltage Range 30-LED RGB Driver TQFN33-16    

+ RGB LED Drivers  

 

Set-top box and audio equipment use multicolor RGB LEDs for function indicator lamps. Indicator lamps show power on or signal connection conditions on devices that use LCD displays. For devices without displays, indicator lamps are needed to show power and all device function status.

 

  • RGB LED drivers allow simplified programmable control of LED color and brightness in an ultra small footprint package device.
  • Kinetic Technologies’ devices feature a wide range of ramp up/down timing for slow fade in/out effects and complex repeating patterns.
  • 3-channel RGB LED drivers permit customer color control.
  • 4-channel RGBW devices allow for driving a white LED in addition to the RGB LED.
  • Programming interface options include ExpressWire or I2C to ease integration with a wide variety of processors and operating systems.

 

Part NumberDescriptionPackagePackage Alt.Package Alt.1
KTD2021 3-Channel RGB LED Driver with ExpressWire Control TSOT23-6    
KTD2022 3-Channel RGB LED Driver with ExpressWire Control UTDFN-8 1.5x1.5mm    
KTD2023 4-Channel RGBW LED Driver with ExpressWire Control UTDFN-8 1.5x1.5mm    
KTD2026 3-Channel RGB LED Driver with I2C Control UTDFN-8 1.5x1.5mm    
KTD2027 4-Channel RGBW LED Driver with I2C Control UTDFN-8 1.5x1.5mm    

+ Power Interface  

 

Set-top box and Audio products often need internal voltage rail on/off control to reduce standby or shutdown state power consumption or to enable/disable specific function circuits while the device is operating.

  • Integrated load switches provide simplified microcontroller I/O controlled power switching to eliminate the need for bias and level shift circuits associated with discrete MOSFET switches.
  • Load switches also provide slew rate limited turn on and shutdown mode reverse current blocking.

 

Part NumberDescriptionPackagePackage Alt.Package Alt.1
KTS1601 SRC P-Ch Load Switch with Reverse Blocking WLCSP-4 1.0 x 1.0mm    
KTS1601-1 SRC P-Ch Load Switch with Reverse Blocking and Output Discharge WLCSP-4 1.0 x 1.0mm    
KTS1605 SRC P-Ch Load Switch with Reverse Blocking WLCSP-6 1.0 x 1.5mm    
KTS1605-1 SRC P-Ch Load Switch with Reverse Blocking and Output Discharge WLCSP-6 1.0 x 1.5mm    
KTS1670 Load Switch with adjustable OVP WLCSP-6 1.0 x 1.2mm    
KTS1671 Load Switch with fixed and adjustable OVP WLCSP-6 1.0 x 1.2mm    
KTS1674 OVP Switch with Reverse Blocking and 100V surge Protection WLCSP-20 2.57 x 2.07mm    
KTS1678 OVP Switch with Single Input, Dual Output Switches with Surge Protection and Individual Enables WLCSP-28 2.96 x 1.67mm    
KTS1679-1 OVP Switch with Single Input, Dual Output Switches with 10V Surge Protection, Individual Enables, Selectable OVP & BAT SNS pin WLCSP-28 2.96 x 1.67mm    
KTS1680 100V Surge Protected OVP Switch WLCSP-12 1.3 x 1.96mm    
KTS1681 Ultra-Fast 100V Surge Protected OVP Switch, with VDET output and MIC function WLCSP-12 1.3 x 1.96mm    
KTS1682 Ultra-Fast 100V Surge Protected OVP Switch, with VDET output and MIC function WLCSP-12 1.3 x 1.96mm    
KTS1685 OVP Switch with 100V Surge Protection WLCSP-9 1.33 x 1.33mm    
KTS1686 Ultra-Fast 100V Surge Protected OVP Switch, with Bidirectional Blocking WLCSP-15 1.6 x 2.1mm    
KTS1688 OVP Switch with Reverse Blocking and Current Limiting WLCSP-9 1.22 x 1.22mm    
KTS1689A 100V Surge Protected OVP Switch WLCSP-12 1.3 x 1.96mm    

+ System Power  

 

New generations of set-top box and audio require increasing levels of features, performance, control and smaller board space. System Power ICs increase the control, performance by integrating multiple functions in a single IC which decreases the overall board area. 

 

  • ICs focused on specfic application areas including mobile phone display power subsystems and multi-channel DC/DC converters optimized for Hi-fi audio. 
  • High efficiency power conversion./li>
  • Smallest board space with fewest external components for a solution.
  • Programming options cover simple PWM signal control to full-featured I2C interfaces.

 

Part NumberDescriptionPackagePackage Alt.Package Alt.1
KTZ8812 +/- Dual Output DC/DC Converter WLCSP-15 2.2x1.45-15 TDFN 3x2.5-14  

Copyright © 2017 Kinetic Technologies, a Cayman Corporation. Privacy Policy | Terms of Use